So I’ve never considered a Voron before. I’m looking at it now and I went through the configurator. I have a spreadsheet of parts and links to the supplier. Do you just order all these parts from the supplier and then I put it together myself? Do I have to solder? I suck at it.
I’ve considered a Prusa. Definitely one of the best (if not the best on the market). I was sort of hoping for a larger print bed.
get kits for the things you want and self source what you want to be picky on. For example, here’s a motion kit
configure a kit from someone like West3D
buy a BOM in a box. There are a couple of brands that do this
I personally went the West3D route. It seems like the LDO and formbot BOM-in-a-box options are popular. If you live near a microcenter they offer smaller kits if you want to mix and match or use a brick and mortar. Self sourcing tends to be expensive due to our collective tendancy to buy higher quality than necessary parts and shipping.
Yes, you will be building the thing from a ton of parts. Yes, it will take you a while. If you’re comfortable building things there’s nothing particular hard about it. You absolutely will not need to solder. Most kits come with premade wiring harness and there’s plenty of complete wiring options available even if you buy components. Depending on your goals, you might need to customize your wiring some. This means crimping, which isn’t hard per say but you’ll probably need to buy a crimper or two and dial in the right amount of squish for your terminal and wire gauge combination. Too much force and you’ll wind up severing the wires. Too little and the terminal will come off the wire. Again, not hard but you’ll probably need to do it a few times before you develop a feel and get consistent.
I see their kit, very cool. I’m alright if I have to solder. My neighbor can help out, they have a complete workbench setup for electronics and I believe they even have the crimpers I would need.
I’m going to go for the 350mm bed. I’m tired of being limited on the build plate of the Vyper. Are there any suggestions for bumping up the base kit? I see there are a lot of options for this kit.
I wouldn’t look for voron stuff at Microcenter unless you feel like there’s no better option. The few times I’ve seen the stuff they sell it all looks like older outdated versions of the parts.
So I’ve never considered a Voron before. I’m looking at it now and I went through the configurator. I have a spreadsheet of parts and links to the supplier. Do you just order all these parts from the supplier and then I put it together myself? Do I have to solder? I suck at it.
I’ve considered a Prusa. Definitely one of the best (if not the best on the market). I was sort of hoping for a larger print bed.
Or you buy a kit from a reputable brand
You have four paths to get parts for a Voron:
I personally went the West3D route. It seems like the LDO and formbot BOM-in-a-box options are popular. If you live near a microcenter they offer smaller kits if you want to mix and match or use a brick and mortar. Self sourcing tends to be expensive due to our collective tendancy to buy higher quality than necessary parts and shipping.
Yes, you will be building the thing from a ton of parts. Yes, it will take you a while. If you’re comfortable building things there’s nothing particular hard about it. You absolutely will not need to solder. Most kits come with premade wiring harness and there’s plenty of complete wiring options available even if you buy components. Depending on your goals, you might need to customize your wiring some. This means crimping, which isn’t hard per say but you’ll probably need to buy a crimper or two and dial in the right amount of squish for your terminal and wire gauge combination. Too much force and you’ll wind up severing the wires. Too little and the terminal will come off the wire. Again, not hard but you’ll probably need to do it a few times before you develop a feel and get consistent.
I see their kit, very cool. I’m alright if I have to solder. My neighbor can help out, they have a complete workbench setup for electronics and I believe they even have the crimpers I would need.
I’m going to go for the 350mm bed. I’m tired of being limited on the build plate of the Vyper. Are there any suggestions for bumping up the base kit? I see there are a lot of options for this kit.
I wouldn’t look for voron stuff at Microcenter unless you feel like there’s no better option. The few times I’ve seen the stuff they sell it all looks like older outdated versions of the parts.